It’s a perfect day to grill on your Pit Boss grill and a family gathering. You turn on the grill and notice that the auger continuously runs, causing an overflow of pellets in the fire pot. You wonder why won’t the Pit Boss auger stop running? What’s causing the problem and how can I fix it?
Pit Boss Auger Won’t Stop Running
If your pellet grill continuously feeds pellets into the firepot, it’s because the pellets are bad, incorrect wiring, too many ashes, bad controller, or the grill is not heating properly.
According to this online forum, this problem is more common than most people think. Unfortunately, many pellet grill owners (not just Pit Boss owners) have to deal with this problem because of the lack of quality control issue when products are mass-produced.
You likely purchased your Pit Boss because you’ve heard how great they cook and how low maintenance they are. You’ll likely be able to operate your grill with no issues most of the time.
However, here’s how to troubleshoot this problem and get our grill working properly again.
What Is The Pit Boss Auger? How Does It Work?
The pellet grill auger is one of the main electrical components of a pellet grill. It is basically a long screw mechanism that feeds pellets into the firepot, based on the speed indicated by the thermostat.
If this is your first time owning a pellet grill, you’ve likely never seen how one starts. The Pit Boss grills run off electricity. Once plugged into an AC outlet, you turn on the grill and the auger starts turning feeding wood pellets into the firepot.
The wood pellets eventually catch fire, which sets the airflow for the grill, and allows you to begin cooking. Watch the video below to see how the auger works to feed pellets into the firepot.
If your auger is working properly, it will feed enough pellets into the firepot and stop once the pellets catch fire. When the auger continuously runs, the pellets will overflow, and you’ll end up with too much smoke and no fire.
Why The Pit Boss Auger Keeps Feeding Pellets
Now that you know what the auger is and how it works, let’s take a look at what causes it to run continuously.
As you know, I own the Pit Boss Pro Series 820, and haven’t experienced this issue. However, I researched tons of online forums, websites, and social media sites to find out what causes this problem and how to fix it.
You’re Experiencing Pit Boss Auger Motor Problems
Most of the time an auger motor failure is due to a jammed auger. Some Pit Boss owners who have experienced a continuously running auger have said that it was due to an auger motor failure.
The Hardwood Pellets Have Moisture
When your pellet grill is stored outside in the elements, it’s likely the hardwood pellets have moisture in them. It’s vital to make sure you properly store the hardwood pellets.
Most people store their pellet grill outside, and leave the pellets in the hopper. That’s perfectly fine, if you don’t have a garage or building to store it in.
However, ensure you’re using a cover to keep both the pellets dry.
The Auger and Fan Connections are Reversed
According to this forum thread, an owner of a brand new Austin XL experienced this problem. After spending hours troubleshooting, he realized the wiring was reversed.
It’s A Vacuum Switch Issue
Whenever you experience auger issues, the first thing that is affected is the vacuum switch. The vacuum switch works in conjunction with the power that connects to the auger motor.
The issue could be due because the vacuum switch is sensing pressure inside the grill, and won’t stop running. It could be because of a buildup of ashes or residue inside the chimney of the stove.
Your Grill Is Not Heating Up Correctly
A pellet grill owner on this Reddit experienced this issue when their grill reached 400℉. The temperature dial was set to the smoke setting, and they had noticed the pellets backing up inside the firepot.
Before they knew it, they had a raging inferno and weren’t sure if it was an auger or thermostat issue.
If you’re noticing auger issues when the temperature reaches 400 degrees, it’s likely the ashes are getting stuck in between the auger motor. This is a rare issue, but it can happen if you’re using the wrong pellets.
This problem usually occurs when you’re using low-quality pellets.
How to Fix Pit Boss Auger Issues
Now that you know the primary reasons of why the Pit Boss pellet grill won’t stop running, let’s look at how to get it running properly again.
Use Dry Pellets
Whenever you buy hardwood pellets, you should take them out of the bag and put them in an airtight 5 gallon container. This will prevent them from being exposed to the elements.
If you’re not sure whether your pellets are good, then do a quick pellet test. If you hear the snap, they are healthy and good to use.
When the pellets are exposed to moisture, they expand, rendering them useless. Dry, healthy pellets will heat up more quickly, and stay ignited longer.
This will also prevent the auger from jamming, or continuously feeding the firepot.
Rewire the Fan and Auger Motor
So how do you check the wiring on your Pit Boss grill? You’ll need to check the wiring diagram on your Pit Boss manual.
Some Pit Boss owners have noticed that the Fan and Auger connections were reversed. Of course, you’ll need to open up the digital control board to check the wiring.
If this is the case, fix the wiring and that should solve the auger issue!
Clean the Ashes and the Chimney
Ensure you’re cleaning your grill and chimney regularly. When it isn’t cleaned properly, eventually, the buildup of ashes and soot in the chimney will obstruct the auger and cause problems.
Check where the chimney is attached to the barrel, that’s where buildup occurs.
Reconnect The Vacuum Switch
If you find that the issue is being caused by the vacuum switch, disconnect the wiring and then reconnect it. Afterward, turn the power on to see if the problem has been fixed or not.
Use High Quality Pellets
Pit Boss recommends using high quality Pit Boss pellets in your smoker. High-quality pellets will ensure your auger motor runs smoothly.
If the auger is running poorly, you will need to clean the debris that was likely caused by poor quality pellets.
Replace The Pit Boss Auger Motor
If you’ve tried all the steps above and the issue isn’t resolved, it may be time to replace the Pit Boss auger. Replacing the auger motor is a lot of work, so I discuss it in this article.
You can also reach out to Pit Boss’s customer support to see what they recommend for the fix. Here’s the contact information.
Most Pit Boss auger problems are easy to troubleshoot and fix. If your auger is feeding pellets continuously, it’s likely due to the reasons mentioned above.
The best tip for keeping your Pit Boss running efficiently is to maintain and care for your grill based on Pit Boss’s recommendations. This includes burn off’s after every cooking session, regular deep cleanings, and proper storage for your grill and pellets.
- Why Isn’t My Pit Boss Heating Up?
- How to Unclog a Pit Boss?
- Why Does My Pit Boss Keep Shutting Down?
Grill Displays Err Code:
A Pit Boss err code is best resolved by unplugging your grill and then restarting everything from scratch. Before you reconnect it to the power socket, check out the temperature sensor and wipe it down.
Troubleshooting the Auger on a Wood Pellet Grill - YouTube
How to Clean or Replace any Pit Boss Auger | Pit Boss Pit Stops - YouTube
How to Replace the Auger and Auger Motor in Your Pellet Grill | Pit Boss ...
Recommended Initial Setting
According to Pit Boss, you should start your first cooking session with the P setting at 4. This is the factory default setting, and it allows the auger to run at 18-second intervals with 115 seconds in between each cycle. This should get the temperature where you need it to be.
Pit Boss models equipped with the P Set feature will have a button on the PID controller and will display the P setting on the LCD control board screen. This setting gives you complete control and can help control cooking time if everything is working correctly.
How to clean an auger on a pellet grill is much simpler. You can use some sandpaper and a wire brush to do so. Clean until it's smooth and the auger screw can move in and out of the hole with ease. At this point, you can put your auger screw back in place and reattach it to the motor.
- Holding the Prime button prevents the auger from pausing, so the pellets arrive more quickly. (Holding the Prime button does not cause the auger to turn faster).
How to Fix A Pellet Stove Auger Jam - YouTube
A Pit boss uses a 120V, 5 AMP fuse.
The “Pit Boss” wood pellet barbecue line, manufactured by Dansons Inc., carries a one (1) year limited warranty for from the date of sale to the original owner only, against defects and workmanship on all steel parts, (excluding the burn pot), and one (1) year on electrical components.
What Does Pit Boss ErH Code Mean? ErH is a common error code that displays on the LCD screen, indicating the Pit Boss grill is overheating.
AUGER FEEDING PELLETS DURING SHUTDOWN
On a WiFIRE-enabled (D2) grill, it's normal for the auger to continue feeding pellets into the firepot during the shutdown. This is an enhanced design feature to prevent the pellets remaining in the auger from catching on fire.
It's normal for the fan of your grill to run while it is in use. Sometimes, it may even continue to run for 4 – 10 minutes after shutting down the grill. There's no need to panic or worry if you experience this on your Pit Boss grill.
How to Replace the Auger Motor on a Traeger Grill - YouTube
- Check the Outlet the grill is plugged into to make sure that it is working properly. This includes making sure the GFCI or Breaker box is not being tripped. - Try the grill in another outlet, or something else in this outlet to ensure that is not the issue.
Grill Isn't Heating to Set Temperature
Pit Boss temperature problems typically arise because the burn pot isn't getting enough oxygen to achieve or maintain the desired temps. Check the burn pot, the air intake, and the fan to make sure there are no obstructions.
Fixing Pit Boss Error Codes! ErH, Er1, NoP, ErL #pitboss #pitbossnation
In most cases, Pit Boss Grills throw error messages because of a dirty temperature probe. With constant use, grease, ash, and dust collect on the temperature sensor, such that it gets to a point where the grease and grime harden around the sensor.
Using dry and good conditioned pellets also helps to fix this issue.. Sometimes, the pit boss auger can create some problems for you, such as it may not stop running.. This causes the pit boss pellet grill auger to keep running until the set temperature is achieved.. The pellets can also be the leading cause of the pit boss pellet grill auger’s constant running.. You can also look at the temperature probe of the pit boss pellet grill auger and wipe it off with a clean fabric to remove any residues that might be causing any hindrance.. If you are looking for a good option, Podoy Pellet Grill Auger Motor is an excellent example of a pellet grill motor that is compatible with most pit boss pellet grills.
You’ll be happy to know your Pit Boss Grill isn’t broken forever; all you need to do is fix your clogged auger.. A Pit Boss pellet grill or pellet smoker uses wood to create a great smoke flavor profile.. One of the main things causing the auger on pellet grills to get jammed is due to wet pellets.. Step 1: Removing The Bottom Panel To start, you’ll want to remove the auger from the Pit Boss.. Step 2: Move The Control Board Next, you’ll need to remove both of the screws from the control board.. Step 3: Move The Hopper On the hopper, you’ll need to remove both the back and front screws.. Similar to the control board, the hopper is attached to the Pit Boss via the power cord so you won’t be able to remove it completely.. Step 4: Remove The Bolt Before you’re able to remove the auger from your Pit Boss, you’ll need to remove the Allen head nut.. Step 5: Remove The Auger Screw Once the motor has been removed, you’ll notice one screw holding the auger in place.. Once you’ve got the auger removed, you can use sandpaper to break off the pellet.. Cleaning up your auger isn’t exactly an easy and quick process, so to save yourself time and ensure your Pit Boss is always working, only use dry pellets in your hopper.
If you have a blocked/jammed auger on your Pit Boss, its likely due to wet pellets and not dry pellets as is shown here in a screenshot from the Pit Boss troubleshooting video: Image – PitBoss-Grills.com. If the pellet feed auger on your Pit Boss pellet grill/smoker won’t turn, there are a couple of potential causes.. Both are potential causes, however, they are not the most likely causes of an auger blockage and in many cases, once the auger is cleaned out, you’ll find the auger motor still works.. The official troubleshooting video from Pit Boss on what to do if you experience an auger blockage: Video – PitBoss-Grills.com The video above from Pit Boss does give good advice on how to avoid a future auger blockage.. This is what its like to remove a jammed auger in the real world Once you have removed the auger, that’s only half of the job, you now need to clean out the auger tube of the expanded sawdust.. While the final stage of the auger removal process is pretty much the same across most Pit Boss models, there are differences when it comes to hopper removal etc to actually get to the auger.. Pit Boss Copper Series Auger Removal Process: Video – PitBoss-Grills.com Image – PitBoss.com. Pit Boss Navigator Series Auger Removal Process: Video – PitBoss-Grills.com Image – PitBoss.com. Pit Boss Sportsman Series Auger Removal Process: Video – PitBoss-Grills.com Image – Lowes.com. Pit Boss Pro Series Auger Removal Process: Video – PitBoss-Grills.com Image – Lowes.com. Pit Boss Pro Series Vertical Smoker Auger Removal Process: Video – PitBoss-Grills.com Image – Walmart.com. Pit Boss Platinum Brunswick Auger Removal Process: Video – PitBoss-Grills.com Ok, let’s say you have followed the steps as shown in the applicable video to your particular Pit Boss model.
One fine morning you open your Pit Boss Grill to cook some meat- but the auger is not turning!. Oftentimes, there are a lot of reasons why the auger on your pit Boss Grill might not be working.. If you have left your pit boss grill open and uncovered in the rain, there is a possibility that your auger has become clogged.. If you had not left your auger out in the open rain, your auger can become blocked because of debris.. A pit boss auger stuck could also be because of motor damage.. If you are sure that your pit boss auger has become clogged, you will have to clean it out as soon as possible.. If you want to clean the auger on your Pit Boss Grill, the first thing that you have to do is detach it from the auger motor.. So, after you have successfully detached the auger from the auger motor, and unplugged all of the wires you can start cleaning the auger itself.. Reattach the auger with the auger motor and plug in the devices to all of their respective receptacles.. Try to clean your pit boss grill auger as often as you can.. What Does The Pit Boss Auger Do?. When the pellets inside the grill are exposed to moisture, they will swell up and clog the auger.. But, in conclusion, the auger not rotating is not a reason for you to replace your pit boss grill entirely.
For a complete take on the P settings on your Pit Boss pellet grill, check out the table below.. Grill Temperature Temperatures are not high enough Most novices have a hard time trying to get their smoker to work at a consistent temperature.. If your Pit Boss pellet grill is not getting to temp, there is a good chance that the firepot isn’t getting the oxygen it needs to reach and maintain the required temperature.. Moreover, if you have cold weather, covering the Pit Boss pellet grill will protect it and you won’t have any issue getting the right temperature.. That’s because the Pit Boss pellet grill functions through the auger turning on and off at set intervals.. Once these flashing dots go away, the grill will start to adjust to the temperature selected, which is the smoke setting for barrel-style pellet grills.
Are you annoyed because your Pit Boss auger making noise and not turning on?. In this article, we will be discussing 5 reasons why the Pit Boss auger motor makes noise and won’t turn on and how to fix it.. The most common reasons behind your pit boss auger not turning or making noiseare stuck pellets in the auger, faulty auger bearings, bent auger screws, obstructed auger fan, and rust build-up in the auger.. It can cause your pit boss auger stuck and thus the auger to squeak while moving and won’t turn on.. You can get rid of this pit boss auger jam and irritating noise just by removing the stuck piece.. Turn off the whole system Remove the auger motor fan and the auger motor from under the hopper Unscrew the auger Pull out the auger push rod from its place Take a look in the auger system vent to see if there are any pellet pieces stuck Clean the inside and remove everything stuck on the auger rod. After this, your Pit Boss smoker’s auger motor won’t be making any noise and turning smothly.. Turn off the whole Pit Boss motor Loosen the auger collar set screws Remove the auger motor Unscrew the bolts on the endplate Don’t hesitate to pry off the silicone sealant Remove the auger and clean the spot Reassemble the new bearings in the auger motor Put the auger motor back to where it was. Disassemble the auger rod from its place and pull it out Roll the auger on a flat surface till the bent is fixed Put more force if needed. Auger fan helps the auger to function in the system.. Detach the bottom panel of the hopper Remove the auger motor panel Look for any sign of obstructions Clean the auger motor and everything blocking the auger fans path Put the panels back to their position. Simply pull out the auger rod, scrub off the rusts, and put the auger back in its place.. See how easy it is to get rid of a Pit Boss auger making noise or not turning on!
Your Pit Boss keeps feeding pellets mainly because of damp pellets, ash build-up, faulty auger-motor wiring, insufficient oxygen supply in the burn pot, faulty vacuum switch, broken controller, and bad weather.. The auger is run by an auger motor placed at the very back of the Pit Boss grill.. If your new Pit Boss auger is continuously running, then the issue lies in the wiring.. And once you have a new burn pot, the perfect air supply in the system will keep the auger running smoothly.. Bad vacuum switch can be the sneaky reason behind a continuously running Pit Boss auger.. Step 4: Clean the auger before installing the new auger motor.
Not really; however, you will need to learn how to unclog the auger on a Pit Boss or any other pellet grill before you can use it again.. To unclog a Pit Boss, you need to remove the bottom panel, control board, detach the hopper, motor, and then remove the screw holding the auger in place.. Phillips screwdriver Allen wrench Socket wrench Pipe wrench Chisel (to break the clogged pellets free) Vacuum (for removing any hard to reach places). If you’re dealing with a Pit Boss auger jam, you’ll have to remove the auger using the steps below.. Once the auger screw is removed, you can clean up the auger.. However, when moisture gets into your hopper, it turns the pellets into mush that can cause the Pit Boss pellet grill to stop working.
The Pit Boss pellet grill is a great tool for outdoor cooking applications.. ErH This message indicates an issue with the heat and temperature control of the pellet grill.. If the grill isn’t overheating, the ErH message might be the result of an improper connection between the probe wire and the temperature control system.. As Pit Boss pellet grill problems go, this is a good one to have—it simply indicates that the unit is working properly.. First of all, it could be because the pellet grill just isn’t plugged in.. It needs to be at least 15 amps in order to power the Pit Boss pellet grill.. When you increase the P setting , you’re decreasing the pellet supply, resulting in more smoke and a lower grill temperature.. Try to keep the grill out of direct sunlight, and avoid grilling when it’s windy or raining outside.. Wood Fired Pellet Grill & Smoker, Smoke, Bake, Roast, Braise and BBQ High temperature powder coated steel Cooking temperature range 180-500 F Digital control board with LED read-out Porcelain coated wire cooking grids Innovative flame broiler for direct flame cooking
In this article, we’ll go over the reasons why your Pit Boss the temperature reading is blinking and failing to raise the temperature and how you can solve it.. When the temperature gets lower than the required level, the blinking feature starts signaling the auger to push in pellets as it thinks that there are not enough pellets to burn .. But if it feeds pellets after pellets, it will only choke out the fire as not enough oxygen is getting in.. If you see that there are enough pellets in the hopper and there is the fire still burning, but the temp is staying low, the issue may be the auger motor.. Pellet burns in the fire and turns into ash.. Yes, no matter what caused the temperature blinking feature to turn on, if you don’t take care of the issue soon, the auger will keep feeding pellets (unless it’s empty).. And if there is an overfilling of pellets as it can happen during temperature blinking, clean the burn pot to restart the grill.. The most likely reason for Pit Boss pellet grill temperature fluctuations is not getting enough oxygen to keep the fire going.
You turn on your grill and suddenly notice that your Pit boss fan is not working.. After you have wrapped up and shut down the Pit boss, just let the fan shut down on its own.. So, if you notice your fan is not working, it’s probably because there is excessive grease and mold stuck in the fan.. This mainly happens when you don’t clean your Pit boss fan from time to time.. Now that we’ve known the reasons behind the Pit boss fan not working, let’s focus on the fixes.. They will fix the Pit boss fan in no time.. One of the main issues of grill fan not working is because of wire issues So firstly check the wire connections.. The fan will run as long the Pit boss grill is running.. As soon as you turn the grill on, the fan will start to work.
Weather is one of the most common causes of temperature issues on Pit Boss Grill.. Adjusting the P setting too frequently or too drastically does cause further temperature issues in your Pit Boss Grill, including massive temperature swings and flame dying out .. Use your Pit Boss Grill at a factory setting of P-4 before adjusting the P setting.. The following video will help you understand the P setting and temperature on your Pit Boss Grill control panel:. If your Pit Boss Grill burn pot has holes, then it’s easy for heat to escape, which results in your grill not heating up.. When the LCD screen on your Pit Boss Grill isn’t lighting up, your grill won’t get hot.. The following video demonstrates how to replace a combustion fan in your Pit Boss Grill:. Turn on the temperature dial and allow your Pit Boss Grill to heat for about 10 to 20 minutes.
Once the grill top is cool, wipe it with an oiled rag to remove any debris on the surface.. Allow it to dry completely before replacing it in the grill.. Wipe down the exterior with a soft cloth and warm water; ensure no excess moisture.. If your fire is too small or there’s no airflow under the grates where you have positioned the food, food will cook but won’t produce smoke.. Next, make sure there are enough pellets in the hopper .. It would be best to be mindful of how often you cook on your pit boss pellet grill and how often you clean it after each use.. Step Five: Wipe clean all pit boss pellet grill surfaces with a cloth or sponge that you have dampened with water.. Step Nine: Replace cooking grates and other components that you have cleaned thoroughly by hand.. To do this, plug in your pit boss pellet grill for 15 minutes, turning the temperature setting to “high,”. Always ensure there is no residual ash or debris left inside the grill before cooking again.
So if your grilling unit is not too old, but you have already noticed certain flaws in its work, or if your Pit Boss grill has problems with temperature, we recommend you check it for any issues.. So below we will take a look at some of the most prevalent problems that your Pit Boss grill may experience, from Pit Boss temperature problems to smoke discoloration.. If you see such a message, it indicates that there is an issue with the heat and temperature control of the pellet grill.. As Pit Boss pellet grill problems go, this is a good one to have, it simply indicates that the unit is working properly.. First of all, it could be because the pellet grill just is not plugged in.. It needs to be at least fifteen amps in order to power the Pit Boss pellet grill.. If this does not work, remove the cooking grates and grease tray so you can take a good look at the igniter.. In this case, you will have to get in touch with Pit Boss and explain the situation so that they can help you with a replacement.. Credits: TransientEternal, via Canva.com When the grill is too hot during the “smoke” function, it means that the P level is set too low.. Make sure the temperature dial is set to “smoke”, then push the P setting button to boost the level.. Credits: golubovy, via Canva.com What if the issue you face is about the fact that your grilling unit simply can’t heat to the temperature you have set for it?. To check whether this is the issue, look inside the hopper and add more pellets, if necessary.. Well, now you are informed about all the most frequent problems and issues that one may have with the pellet grill unit.. Credits: romaset, via Canva.com Even though you are now informed about the most common flaws in a pellet grill work, it is still necessary to maintain the unit properly.. In addition, a properly cleaned grill will be working much better and grill your foods more effectively and thoroughly!
Open the lid and set the temperature dial to “Smoke.” The smoke setting temperature range is 180-210° F/ 80-100° C. Press the start button on the pellet grill, and you will hear the fan running.. The Prime feature on the Pit Boss pellet grills speeds up the auger so that the pellets fill it quickly and get to the firepot before the pellet grill shuts down from lack of pellets dropping into the firepot.. In contrast to other grills, pellet grills don’t burn themselves out.. Grill exterior Use a soft rag and a grill cleaner to clean the grill exterior.. Turn the pellet grill on and turn the temperature dial to “Smoke.” Increase the grill temperature to the highest setting (over 233°C / 450°F).. Remove all the cooking components from the grill if you run out of pellets while grilling.. If your grill doesn’t have a prime button, smoke the grill for a while and then allow the pellets to light up.. Typically, the Pit Boss grill fan stops working overtime due to poor grill maintenance and grease buildup, hindering its movement.. If you notice your Pit Boss pellet grill is not smoking, there be an issue with grill temperature, pellets, meat temperature, or firepot.. To get more smoke out of your Pit Boss pellet grill, you need to:. If your Pit Boss pellet grill is not maintaining its temperature correctly, here is how you can improve temperature control.. But if you follow our Pit Boss grill troubleshooting guide, you’ll have your grill in perfect condition in no time.
Here is everything you need to know about Pit Boss pellet grill troubleshooting:. Several components can be fixed if your Pit Boss is not turning on.. Replace the 5-amp fuse at the back of your control panel if the grill does not turn on.. You can also check the auger to make sure it’s not feeding pellets into your firebox.. If your grill is old, you can check the igniter and then follow the instructions.. Pit Boss might not smoke, so you may assume the smoker is damaged and needs to be replaced.. Also, make sure you check the fan to ensure it is functioning correctly.. This is how to adjust Pit Boss grills’ P settings.Make sure the temperature dial is set for Smoke.. A grease fire in your cooking chamber might cause you to get an ErH message.. Pit Boss Customer Care can help you determine the problem if your auger isn’t jammed.. This is the smoke setting used for barrel-style pellet grills.
If your Pit Boss auger is not turning, there are a few possible reasons why.. If you think this might be the problem, the first thing you’ll want to do is check the auger for any blockages.. If you think this might be the issue, you’ll need to check the auger motor to see if it is receiving power.. If your Pit Boss smoker is not heating up, there are a few things you can check to troubleshoot the issue.. The next time you’re firing up your Pit Boss smoker, be sure to use the correct setting for what you’re cooking.
If your stove starts up normally but shuts down with a fire burning within 30 minutes every time, the proof of fire sensor is either dirty or needs to be replaced.. Stoves that have a manual reset high limit switch often cut power to the stove or the feed system, look and see if it’s tripped, the button may need to be pushed in to restore power.. The Power To The Feed Motor Is being Interrupted When the stove is running, the combustion motor is moving air through the stove.. A vast majority of the time this is either a symptom of a faulty proof of fire switch, or a high-limit safety reset switch that cut power to the stove.. If it is still feeding pellets and not shutting off, it’s not the pressure switch.
Why Does Pit Boss Pellet Grill Temperature Fluctuate? 11 Different Ways to Minimize It! - Top Home Apps ›
While smoking or grilling process is going on, the grill temperature drops.. It means when pellets are added to the grill fire, the temperature goes high and the controller limits the delivering pellets till the temperature swing goes down.. The temperature of the pellet may swing due to a lot of other reasons such as heavy food load, the opening of the grill door frequently, stacking food too close at the sides of the grill grates, etc.. This is an important step to prevent temperature fluctuation and helps grill for constant stable temperature while cooking.. While smoking or temperature below 200 ° F, if you experience temperature fluctuation, try to adjust the “P” setting located on your pellet grill.. If you are opening or closing the grill door frequently, you may experience the temperature fluctuation in the grill.. The one more reason is that water temperature takes longer to rise or fall in temperature which surely helps for temperature fluctuations.. Now you know the causes for Pit boss pellet grill temperature fluctuation and how to minimize it.
Like all pellet grills, the Traeger grill has some limitations and lackings.. This problem is almost the same as temperature swings.. The Traeger grill has an induction fan.. The wood pellets are producing less smoke.. This problem is the root of many other problems like temperature swings, excessive ash, etc.. Traeger Grills temperature oscillation?. Now you can solve your Traeger grill problem with this troubleshooting solution.